Plumbing Basics: Your Starting Point for Bathtub Installation
Plumbing Basics: Your Starting Point for Bathtub Installation
Blog Article
Have you been in search of tips on How to Install a Bathtub Yourself?
Mounting a bathtub isn't specifically rocket science, however it does need solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old tub is conveniently available, the task can relocate rapidly; if you have to open a wall to remove the old bathtub as well as place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the work and also fit trying it. As opposed to employing a service provider to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might need a professional plumber to make tube connections.
This post will aid you install a new tub in your bathroom if you have already acquired a brand-new tub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices and material list ought to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite problematic as a result of the limited accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will come from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in location in between the faucet and the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet ports. The previous kind needs to be connected to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and changing the feet on the bathtub until the level checks out level.
To install taps, fit all-time low of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the supply of water and examine all joints and brand-new pipework for leaks and tighten them if needed. Load the bathtub as well as additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used at the very least once as this will resolve it into its last position.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a stiff seal, causing the water to pass through the wall surface in between the bath as well as the tiling, causing issues with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to permit the movement experienced when the tub remains in use. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed reading my piece. Sharing is good. Helping people is fun. Thanks a lot for your time spent reading it.
Need urgent plumbing repairs? Call. Report this page